96d6e190e9
There are some known limitations for now,
* Do not shrink the length of the uleb128 value, even if the value is reduced
after relaxations. Also reports error if the length grows up.
* The R_RISCV_SET_ULEB128 needs to be paired with and be placed before the
R_RISCV_SUB_ULEB128.
bfd/
* bfd-in2.h: Regenerated.
* elfnn-riscv.c (perform_relocation): Perform R_RISCV_SUB_ULEB128 and
R_RISCV_SET_ULEB128 relocations. Do not shrink the length of the
uleb128 value, and report error if the length grows up. Called the
generic functions, _bfd_read_unsigned_leb128 and _bfd_write_unsigned_leb128,
to encode the uleb128 into the section contents.
(riscv_elf_relocate_section): Make sure that the R_RISCV_SET_ULEB128
must be paired with and be placed before the R_RISCV_SUB_ULEB128.
* elfxx-riscv.c (howto_table): Added R_RISCV_SUB_ULEB128 and
R_RISCV_SET_ULEB128.
(riscv_reloc_map): Likewise.
(riscv_elf_ignore_reloc): New function.
* libbfd.h: Regenerated.
* reloc.c (BFD_RELOC_RISCV_SET_ULEB128, BFD_RELOC_RISCV_SUB_ULEB128):
New relocations to support .uleb128 subtraction.
gas/
* config/tc-riscv.c (md_apply_fix): Added BFD_RELOC_RISCV_SET_ULEB128
and BFD_RELOC_RISCV_SUB_ULEB128.
(s_riscv_leb128): Updated to allow uleb128 subtraction.
(riscv_insert_uleb128_fixes): New function, scan uleb128 subtraction
expressions and insert fixups for them.
(riscv_md_finish): Called riscv_insert_uleb128_fixes for all sections.
include/
* elf/riscv.h ((R_RISCV_SET_ULEB128, (R_RISCV_SUB_ULEB128): Defined.
ld/
* testsuite/ld-riscv-elf/ld-riscv-elf.exp: Updated.
* testsuite/ld-riscv-elf/uleb128*: New testcase for uleb128 subtraction.
binutils/
* testsuite/binutils-all/nm.exp: Updated since RISCV supports .uleb128.
I noticed in the binutile Makefile that runtest is being invoked with
CC, CC_FOR_BUILD and other compiler related flags in the environment.
That doesn't work. Those variables ought to be passed on the runtest
command line.
After fixing that I had some fails due to binutils testprog.c now
being compiled with the default "-g -O2" picked up in
CFLAGS_FOR_TARGET. Hack around that by passing -O0.
Also, with the binutils testsuite now taking notice of CC_FOR_TARGET,
I found a couple of debuginfod.exp fails with one of my compilers that
happened to be built without --debug-id being enabled by default.
* Makefile.am (check-DEJAGNU): Pass $CC and other variable on
the runtest command line rather than futilely in the
environment. Add -O0 to CFLAGS_FOR_TARGET.
* Makefile.in: Regenerate.
* testsuite/binutils-all/debuginfod.exp: Compile testprog.c
with -Wl,--build-id.
For MIPS64r6 ports, Debian as an example, `mipsisa64r6el` is
used as the cpu name in triple.
Let's recognize them by `mips*64*(el)`.
For 64bit Ports, like Debian's mips64el and mips64r6el ports,
`gnuabi64` is used as the abi section.
Let's use N64 abi by default for the triple with gnuabi64.
On DOS systems, absolute paths start with the drive letter. This can
trigger failures in the regexp from dump tests, especially for those
checking for warnings or errors. They are usually skipping everything
before the first ":" as it has to be the file path.
| [^:]*: warning: ...
In order to avoid modifying many regexps to allow such drive letters,
prune them from all the outputs if they are found at the beginning of
a line.
binutils/ChangeLog:
* testsuite/lib/binutils-common.exp (prune_dump_output): New
(run_dump_test): Use it.
ld/ChangeLog:
* testsuite/ld-elf/noinit-sections-2.l: Remove DOS drive letter
handler.
Fix these fails:
alpha-dec-vms +FAIL: ld-scripts/asciz
alpha-dec-vms +FAIL: ld-scripts/ascii
i386-go32 +FAIL: ld-scripts/asciz
sh-coff +FAIL: ld-scripts/asciz
It's better to positively select targets for .section support than to
try to exclude all targets that don't. Make a new is_coff_format so
we can easily select such.
binutils/
* testsuite/lib/binutils-common.exp (is_coff_format): New.
ld/
* testsuite/ld-scripts/ascii.d: Use is_elf_format and
is_coff_format to select targets, exclude ti coff.
* testsuite/ld-scripts/asciz.d: Likewise. Accept trailing zeros.
Before commit:
commit 2438b771ee
Date: Wed Nov 2 15:53:43 2022 +0000
opcodes/mips: use .word/.short for undefined instructions
unknown 32-bit microMIPS instructions were disassembled as a raw
32-bit number with no '.word' directive. The above commit changed
this and added a '.word' directive before the 32-bit number.
It was pointed out on the mailing list, that for microMIPS it would be
better to display such 32-bit instructions using a '.short' directive
followed by two 16-bit values.
This commit updates the mips disassembler to do this, and adds a new
test that validates this output.
Insn width granularity being 16 bits, producing byte granular output
isn't very useful. With there being a way to specific otherwise
unknown insns to the assembler, use that same representation (to be
precise: its <length>,<encoding> flavor) for disassembly.
This adjusts the testsuite to get rid of a number of XPASSes that have
appeared. Someone might like to look into a better patch for the s390
change.
aarch64-pe XPASS: weak symbols
arm-nacl XPASS: rgn-over8
mcore-pe XPASS: ld-scripts/provide-8
mips64-linux-gnuabi64 XPASS: vers4
mips64-linux-gnuabi64 XPASS: vers4b
mips-linux-gnu XPASS: vers4
mips-linux-gnu XPASS: vers4b
s390-linux-gnu XPASS: undefined line
sh4-linux-gnu XPASS: --gc-sections with __start_SECTIONNAME
sh-coff XPASS: objcopy object (simple copy)
sh-coff XPASS: objcopy executable (pr25662)
binutils/
* testsuite/binutils-all/objcopy.exp: Don't xfail "simple
copy" and "pr25662" on sh-*-coff. Remove all non-ELF xfails
on "ELF unknown section type" test.
ld/
* testsuite/ld-elfvers/vers.exp (vers4, vers4b): Don't xfail
all mips, just xfail mips irix.
* testsuite/ld-gc/pr19161.d: Don't xfail sh.
* testsuite/ld-scripts/rgn-over8-ok.d: Don't xfail nacl.
* testsuite/ld-scripts/weak.exp: Don't xfail aarch64-pe.
* testsuite/ld-undefined/undefined.exp: Conditionally xfail
"undefined line" depending on gcc version for s390.
Delete a few files only used for obsolete targets, and tidy config,
xfails and other pieces of support specific to those targets. And
since I was editing target triplets in test files, fix the nm
alpha-linuxecoff fails.
The newer update-copyright.py fixes file encoding too, removing cr/lf
on binutils/bfdtest2.c and ld/testsuite/ld-cygwin/exe-export.exp, and
embedded cr in binutils/testsuite/binutils-all/ar.exp string match.
While working on disassembler styling for MIPS, I noticed that
undefined instructions are printed by the disassembler as raw number
with no assembler directive prefix (e.g. without .word or .short).
I think adding something like .word, or .short, helps to make it
clearer the size of the value that is being displayed, and is inline
with what many of the other libopcode disassemblers do.
In this commit I've added the .word and .short directives, and updated
all the tests that I spotted that failed as a result.
PR 25202
bfd * bfd.c (VerilogDataEndianness): New variable.
(verilog_write_record): Use VerilogDataEndianness, if set, to
choose the endianness of the output.
(verilog_write_section): Adjust the address by the data width.
binutils* objcopy.c (copy_object): Set VerilogDataEndianness to the
endianness of the input file.
(copy_main): Verifiy the value set by the --verilog-data-width
option.
* testsuite/binutils-all/objcopy.exp: Add tests of the new behaviour.
* testsuite/binutils-all/verilog-I4.hex: New file.
For now, xfail the new test. Some header/aux-header rewriting is
required at the very least.
* testsuite/binutils-all/rename-section-01.d: xfail xcoff.
This tidies SEC_RELOC handling in bfd, in the process fixing a bug
with objcopy when renaming sections.
bfd/
* reloc.c (_bfd_generic_set_reloc): Set/clear SEC_RELOC depending
on reloc count.
* elf64-sparc.c (elf64_sparc_set_reloc): Likewise.
binutils/
* objcopy.c (copy_relocations_in_section): Remove now unnecessary
clearing of SEC_RELOC.
* testsuite/binutils-all/rename-section-01.d: New test.
* testsuite/binutils-all/objcopy.exp: Run it.
gas/
* write.c (size_seg): Remove unneccesary twiddle of SEC_RELOC.
(write_relocs): Likewise. Always call bfd_set_reloc.
Update expected PR binutils/26160 test output for readelf out change
and run PR binutils/26160 test.
PR binutils/26160
* testsuite/binutils-all/pr26160.r: Updated.
* testsuite/binutils-all/readelf.exp: Run PR binutils/26160 test.
This commit adds disassembler styling for the ARM architecture.
The ARM disassembler is driven by several instruction tables,
e.g. cde_opcodes, coprocessor_opcodes, neon_opcodes, etc
The type for elements in each table can vary, but they all have one
thing in common, a 'const char *assembler' field. This field
contains a string that describes the assembler syntax of the
instruction.
Embedded within that assembler syntax are various escape characters,
prefixed with a '%'. Here's an example of a very simple instruction
from the arm_opcodes table:
"pld\t%a"
The '%a' indicates a particular type of operand, the function
print_insn_arm processes the arm_opcodes table, and includes a switch
statement that handles the '%a' operand, and takes care of printing
the correct value for that instruction operand.
It is worth noting that there are many print_* functions, each
function handles a single *_opcodes table, and includes its own switch
statement for operand handling. As a result, every *_opcodes table
uses a different mapping for the operand escape sequences. This means
that '%a' might print an address for one *_opcodes table, but in a
different *_opcodes table '%a' might print a register operand.
Notice as well that in our example above, the instruction mnemonic
'pld' is embedded within the assembler string. Some instructions also
include comments within the assembler string, for example, also from
the arm_opcodes table:
"nop\t\t\t@ (mov r0, r0)"
here, everything after the '@' is a comment that is displayed at the
end of the instruction disassembly.
The next complexity is that the meaning of some escape sequences is
not necessarily fixed. Consider these two examples from arm_opcodes:
"ldrex%c\tr%12-15d, [%16-19R]"
"setpan\t#%9-9d"
Here, the '%d' escape is used with a bitfield modifier, '%12-15d' in
the first instruction, and '%9-9d' in the second instruction, but,
both of these are the '%d' escape.
However, in the first instruction, the '%d' is used to print a
register number, notice the 'r' immediately before the '%d'. In the
second instruction the '%d' is used to print an immediate, notice the
'#' just before the '%d'.
We have two problems here, first, the '%d' needs to know if it should
use register style or immediate style, and secondly, the 'r' and '#'
characters also need to be styled appropriately.
The final thing we must consider is that some escape codes result in
more than just a single operand being printed, for example, the '%q'
operand as used in arm_opcodes ends up calling arm_decode_shift, which
can print a register name, a shift type, and a shift amount, this
could end up using register, sub-mnemonic, and immediate styles, as
well as the text style for things like ',' between the different
parts.
I propose a three layer approach to adding styling:
(1) Basic state machine:
When we start printing an instruction we should maintain the idea
of a 'base_style'. Every character from the assembler string will
be printed using the base_style.
The base_style will start as mnemonic, as each instruction starts
with an instruction mnemonic. When we encounter the first '\t'
character, the base_style will change to text. When we encounter
the first '@' the base_style will change to comment_start.
This simple state machine ensures that for simple instructions the
basic parts, except for the operands themselves, will be printed in
the correct style.
(2) Simple operand styling:
For operands that only have a single meaning, or which expand to
multiple parts, all of which have a consistent meaning, then I
will simply update the operand printing code to print the operand
with the correct style. This will cover a large number of the
operands, and is the most consistent with how styling has been
added to previous architectures.
(3) New styling syntax in assembler strings:
For cases like the '%d' that I describe above, I propose adding a
new extension to the assembler syntax. This extension will allow
me to temporarily change the base_style. Operands like '%d', will
then print using the base_style rather than using a fixed style.
Here are the two examples from above that use '%d', updated with
the new syntax extension:
"ldrex%c\t%{R:r%12-15d%}, [%16-19R]"
"setpan\t%{I:#%9-9d%}"
The syntax has the general form '%{X:....%}' where the 'X'
character changes to indicate a different style. In the first
instruction I use '%{R:...%}' to change base_style to the register
style, and in the second '%{I:...%}' changes base_style to
immediate style.
Notice that the 'r' and '#' characters are included within the new
style group, this ensures that these characters are printed with
the correct style rather than as text.
The function decode_base_style maps from character to style. I've
included a character for each style for completeness, though only
a small number of styles are currently used.
I have updated arm-dis.c to the above scheme, and checked all of the
tests in gas/testsuite/gas/arm/, and the styling looks reasonable.
There are no regressions on the ARM gas/binutils/ld tests that I can
see, so I don't believe I've changed the output layout at all. There
were two binutils tests for which I needed to force the disassembler
styling off.
I can't guarantee that I've not missed some untested corners of the
disassembler, or that I might have just missed some incorrectly styled
output when reviewing the test results, but I don't believe I've
introduced any changes that could break the disassembler - the worst
should be some aspect is not styled correctly.
* testsuite/binutils-all/addr2line.exp: Tidy. For powerpc64
arrange to pass --synthetic to nm, and extract .main and .fn
symbol address for addr2line test. Handle default executable
extension on cygwin/mingw compilers.
PR29397 PR29563: Add new configure option --with-zstd which defaults to
auto. If pkgconfig/libzstd.pc is found, define HAVE_ZSTD and support
zstd compressed debug sections for most tools.
* bfd: for addr2line, objdump --dwarf, gdb, etc
* gas: support --compress-debug-sections=zstd
* ld: support ELFCOMPRESS_ZSTD input and --compress-debug-sections=zstd
* objcopy: support ELFCOMPRESS_ZSTD input for
--decompress-debug-sections and --compress-debug-sections=zstd
* gdb: support ELFCOMPRESS_ZSTD input. The bfd change references zstd
symbols, so gdb has to link against -lzstd in this patch.
If zstd is not supported, ELFCOMPRESS_ZSTD input triggers an error. We
can avoid HAVE_ZSTD if binutils-gdb imports zstd/ like zlib/, but this
is too heavyweight, so don't do it for now.
```
% ld/ld-new a.o
ld/ld-new: a.o: section .debug_abbrev is compressed with zstd, but BFD is not built with zstd support
...
% ld/ld-new a.o --compress-debug-sections=zstd
ld/ld-new: --compress-debug-sections=zstd: ld is not built with zstd support
% binutils/objcopy --compress-debug-sections=zstd a.o b.o
binutils/objcopy: --compress-debug-sections=zstd: binutils is not built with zstd support
% binutils/objcopy b.o --decompress-debug-sections
binutils/objcopy: zstd.o: section .debug_abbrev is compressed with zstd, but BFD is not built with zstd support
...
```
c++filt is always named cxxfilt in a build directory, but in a install
directory it would be named either cxxfilt or c++filt (depending on
the host). Handle this last case in testsuite.
binutils/ChangeLog:
* testsuite/config/default.exp (CXXFILE): if cxxfilt not found,
try c++filt.
When launching the testsuite through runtest outside the build tree,
gentestdlls might not be available, this binary being created by make
check.
Simply untested the related tests instead of crashing.
binutils/ChangeLog:
* testsuite/binutils-all/objdump.exp: Skip dotnet tests if
gentestdlls is not available.
This changes readelf output a little, removing the 0x prefix on hex
output when the value is 0, except in cases where a fixed field
width is shown. %#010x is not a good replacement for 0x%08x.
This adds support for efi-loongarch64 by virtue of adding a new PEI target
pei-loongarch64. This is not a full target and only exists to support EFI at
this time.
This means that this target does not support relocation processing and is mostly
a container format. This format has been added to elf based loongarch64 targets
such that efi images can be made natively on Linux.
However this target is not valid for use with gas but only with objcopy.
We should't limit addresses to 32-bits for 64-bit vma, otherwise there will be
"RVA truncated" error when using objcopy on loongarch64.
With these changes the resulting file is recognized as an efi image.
Any magic number is based on the Microsoft PE specification [1].
The test results are as follows:
$ make check-binutils RUNTESTFLAGS='loongarch64.exp'
PASS: Check if efi app format is recognized
$ objdump -h -f tmpdir/loongarch64copy.o
tmpdir/loongarch64copy.o: file format pei-loongarch64
architecture: Loongarch64, flags 0x00000132:
EXEC_P, HAS_SYMS, HAS_LOCALS, D_PAGED
start address 0x0000000000000000
Sections:
Idx Name Size VMA LMA File off Algn
0 .text 0000003c 00000000200000b0 00000000200000b0 00000200 2**2
CONTENTS, ALLOC, LOAD, READONLY, CODE
[1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format
bfd:
* .gitignore (pe-loongarch64igen.c): New.
* Makefile.am (pei-loongarch64.lo, pe-loongarch64igen.lo, pei-loongarch64.c,
pe-loongarch64igen.c): Add support.
* Makefile.in: Likewise.
* bfd.c (bfd_get_sign_extend_vma): Add pei-loongarch64.
* coff-loongarch64.c: New file.
* coffcode.h (coff_set_arch_mach_hook, coff_set_flags,
coff_write_object_contents) Add loongarch64 (loongarch64_pei_vec) support.
* config.bfd: Likewise.
* configure: Likewise.
* configure.ac: Likewise.
* libpei.h (GET_OPTHDR_IMAGE_BASE, PUT_OPTHDR_IMAGE_BASE,
GET_OPTHDR_SIZE_OF_STACK_RESERVE, PUT_OPTHDR_SIZE_OF_STACK_RESERVE,
GET_OPTHDR_SIZE_OF_STACK_COMMIT, PUT_OPTHDR_SIZE_OF_STACK_COMMIT,
GET_OPTHDR_SIZE_OF_HEAP_RESERVE, PUT_OPTHDR_SIZE_OF_HEAP_RESERVE,
GET_OPTHDR_SIZE_OF_HEAP_COMMIT, PUT_OPTHDR_SIZE_OF_HEAP_COMMIT,
GET_PDATA_ENTRY, _bfd_peLoongArch64_bfd_copy_private_bfd_data_common,
_bfd_peLoongArch64_bfd_copy_private_section_data,
_bfd_peLoongArch64_get_symbol_info, _bfd_peLoongArch64_only_swap_filehdr_out,
_bfd_peLoongArch64_print_private_bfd_data_common,
_bfd_peLoongArch64i_final_link_postscript,
_bfd_peLoongArch64i_only_swap_filehdr_out, _bfd_peLoongArch64i_swap_aouthdr_in,
_bfd_peLoongArch64i_swap_aouthdr_out, _bfd_peLoongArch64i_swap_aux_in,
_bfd_peLoongArch64i_swap_aux_out, _bfd_peLoongArch64i_swap_lineno_in,
_bfd_peLoongArch64i_swap_lineno_out, _bfd_peLoongArch64i_swap_scnhdr_out,
_bfd_peLoongArch64i_swap_sym_in, _bfd_peLoongArch64i_swap_sym_out,
_bfd_peLoongArch64i_swap_debugdir_in, _bfd_peLoongArch64i_swap_debugdir_out,
_bfd_peLoongArch64i_write_codeview_record,
_bfd_peLoongArch64i_slurp_codeview_record,
_bfd_peLoongArch64_print_ce_compressed_pdata): New.
* peXXigen.c (_bfd_XXi_swap_aouthdr_in, _bfd_XXi_swap_aouthdr_out,
_bfd_XXi_swap_scnhdr_out, pe_print_pdata, _bfd_XX_print_private_bfd_data_common,
_bfd_XX_bfd_copy_private_section_data, _bfd_XXi_final_link_postscript):
Support COFF_WITH_peLoongArch64,
* pei-loongarch64.c: New file.
* peicode.h (coff_swap_scnhdr_in, pe_ILF_build_a_bfd, pe_ILF_object_p):
Support COFF_WITH_peLoongArch64.
(jtab): Add dummy entry that traps.
* targets.c (loongarch64_pei_vec): New.
binutils
* testsuite/binutils-all/loongarch64/loongarch64.exp: New file.
* testsuite/binutils-all/loongarch64/pei-loongarch64.d: New test.
* testsuite/binutils-all/loongarch64/pei-loongarch64.s: New test.
include
* coff/loongarch64.h: New file.
* coff/pe.h (IMAGE_FILE_MACHINE_LOONGARCH64): New.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
PR 29457
* objdump.c (disassembler_color): Change type to an enum.
(disassembler_extended_color): Remove.
(usage): Update.
(objdump_color_for_assembler_style): Update.
(main): Update initialisation of disassembler_color. If not
initialised via a command line option, set based upon terminal
output.
* doc/binutils.texi: Update description of disassmbler-color
option.
* testsuite/binutils-all/arc/objdump.exp: Add
--disassembler-color=off option when disassembling.
* testsuite/binutils-all/arm/objdump.exp: Likewise.
* dwarf.c (dwarf_select_sections_by_name): If the entry's value is
zero then clear the corresponding variable.
(dwarf_select_sections_by_letters): Likewise.
* testsuite/binutils-all/debuginfo.exp: Expect -WE and -wE
debuginfod tests to fail.
PR 29267
* dwarf.c (display_debug_rnglists): New function, broken out of..
(display_debug_ranges): ... here.
(read_and_display_attr_value): Correct calculation of index
displayed for DW_FORM_loclistx and DW_FORM_rnglistx.
* testsuite/binutils-all/x86-64/pr26808.dump: Update expected
output.
* dwarf.c (fetch_indexed_string): Do not use length of first table
in string section as the length of every table in the section.
* testsuite/binutils-all/pr26112.r: Update expected output.
* dwarf.c (dwarf_select_sections_by_names): Return zero if no
sections were selected.
(dwarf_select_sections_by_letters): Likewise.
* dwarf.h: (dwarf_select_sections_by_names): Update prototype.
(dwarf_select_sections_by_letters): Update prototype.
* objdump.c (might_need_separate_debug_info): New function.
(dump_bfd): Call new function before attempting to load separate
debug info files.
(main): Do not enable dwarf section dumping for -WK or -WN.
* readelf.c (parse_args): Do not enable dwarf section dumping for
-wK or -wN.
(might_need_separate_debug_info): New function.
(process_object): Call new function before attempting to load
separate debug info files.
* testsuite/binutils-all/debuginfo.exp: Expect -WE and -wE
debuginfod tests to pass.
* testsuite/binutils-all/objdump.Wk: Add extra regexps.
* testsuite/binutils-all/readelf.k: Add extra regexps.
PR 29135
* nm.c (non_weak): New variable.
(filter_symbols): When non-weak is true, ignore weak symbols.
(long_options): Add --no-weak.
(usage): Mention --no-weak.
(main): Handle -W/--no-weak.
* doc/binutils.texi: Document new feature.
* NEWS: Mention the new feature.
* testsuite/binutils-all/nm.exp: Add test of new feature.
* testsuite/binutils-all/no-weak.s: New test source file.
PR 29072
bfd * elflink.c (bfd_elf_size_dynamic_sections): Display a note to the
user that the current ehaviour of creating an executable stack
because of a missing .note.GNU-stack section is deprecated and
will be changed in a future release.
binutils* testsuite/lib/binutils-common.exp (prune_warnings_extra): Filter
out notes about the executable stacjk behaviour beign deprecated.
ld * testsuite/ld-elf/pr29072.b.warn: Update to include the note
about the linker's behaviour being depreccated.
PR 28981
* dwarf.c (fetch_indexed_value): Rename to fecth_indexed_addr and
return the address, rather than a string.
(fetch_indexed_value): New function - returns a value indexed by a
DW_FORM_loclistx or DW_FORM_rnglistx form.
(read_and_display_attr_value): Add support for DW_FORM_loclistx
and DW_FORM_rnglistx.
(process_debug_info): Load the loclists and rnglists sections.
(display_loclists_list): Add support for DW_LLE_base_addressx,
DW_LLE_startx_endx, DW_LLE_startx_length and
DW_LLE_default_location.
(display_offset_entry_loclists): New function. Displays a
.debug_loclists section that contains offset entry tables.
(display_debug_loc): Call the new function.
(display_debug_rnglists_list): Add support for
DW_RLE_base_addressx, DW_RLE_startx_endx and DW_RLE_startx_length.
(display_debug_ranges): Display the contents of the section's
header.
* dwarf.h (struct debug_info): Add loclists_base field.
* testsuite/binutils-all/dw5.W: Update expected output.
* testsuite/binutils-all/x86-64/pr26808.dump: Likewise.
* dwarf.c (use_debuginfod): New variable. Set to 1.
(load_separate_debug_info): Only call
debuginfod_fetch_separate_debug_info is use_debuginfod is true.
(dwarf_select_sections_by_names): Add do-not-use-debuginfod and
use-debuginfod options.
(dwarf_select_sections_by_letters): Add D and E options.
* dwarf.h (use_debuginfod): New extern.
* objdump.c (usage): Mention the new options.
* readelf.c (usage): Likewise.
* doc/binutils.texi: Document the new options.
* doc/debug-options.texi: Describe the new options.
* NEWS: Mention the new feature.
* testsuite/binutils-all/debuginfod.exp: Add tests of the new
options.
Correct issues with INSN2_ALIAS annotation for branch instructions:
- regular MIPS BEQZ/L and BNEZ/L assembly instructions are idioms for
BEQ/L and BNE/L respectively with the `rs' operand equal to $0,
- microMIPS 32-bit BEQZ and BNEZ assembly instructions are idioms for
BEQ and BNE respectively with the `rt' operand equal to $0,
- regular MIPS BAL assembly instruction is an idiom for architecture
levels of up to the MIPSr5 ISA and a machine instruction on its own
from the MIPSr6 ISA up.
Add missing annotation to BEQZ/L and BNEZ/L accordingly then and add a
new entry for BAL for the MIPSr6 ISA, correcting a disassembly bug:
$ mips-linux-gnu-objdump -m mips:isa64r6 -M no-aliases -d bal.o
bal.o: file format elf32-tradlittlemips
Disassembly of section .text:
00000000 <foo>:
0: 04110000 0x4110000
...
$
Add test cases accordingly.
Parts for regular MIPS BEQZ/L and BNEZ/L instructions from Sagar Patel.
2022-03-06 Maciej W. Rozycki <macro@orcam.me.uk>
binutils/
* testsuite/binutils-all/mips/mips1-branch-alias.d: New test.
* testsuite/binutils-all/mips/mips1-branch-noalias.d: New test.
* testsuite/binutils-all/mips/mips2-branch-alias.d: New test.
* testsuite/binutils-all/mips/mips2-branch-noalias.d: New test.
* testsuite/binutils-all/mips/mips32r6-branch-alias.d: New test.
* testsuite/binutils-all/mips/mips32r6-branch-noalias.d: New
test.
* testsuite/binutils-all/mips/micromips-branch-alias.d: New
test.
* testsuite/binutils-all/mips/micromips-branch-noalias.d: New
test.
* testsuite/binutils-all/mips/mips-branch-alias.s: New test
source.
* testsuite/binutils-all/mips/micromips-branch-alias.s: New test
source.
* testsuite/binutils-all/mips/mips.exp: Run the new tests.
2022-03-06 Sagar Patel <sagarmp@cs.unc.edu>
Maciej W. Rozycki <macro@orcam.me.uk>
opcodes/
* mips-opc.c (mips_builtin_opcodes): Fix INSN2_ALIAS annotation
for "bal", "beqz", "beqzl", "bnez" and "bnezl" instructions.
* micromips-opc.c (micromips_opcodes): Likewise for "beqz" and
"bnez" instructions.
Add a test for commit 7c4643efe7, which fixed --only-keep-debug for ELF
relocatables.
* testsuite/binutils-all/objcopy.exp
(keep_debug_symbols_for_elf_relocatable): New test.
PowerPC64 takes a more traditional approach to DT_RELR than x86. Count
relative relocs in check_relocs, allocate space for them and output in
the usual places but not doing so when enable_dt_relr. DT_RELR is
sized in the existing ppc stub relaxation machinery, run via the
linker's ldemul_after_allocation hook. DT_RELR is output in the same
function that writes ppc stubs, run via ldemul_finish.
This support should be considered experimental.
bfd/
* elf64-ppc.c (struct ppc_local_dyn_relocs): Renamed from
ppc_dyn_relocs. Add rel_count field. Update uses.
(struct ppc_dyn_relocs): New. Replace all uses of elf_dyn_relocs.
(struct ppc_link_hash_table): Add relr_alloc, relr_count and
relr_addr.
(ppc64_elf_copy_indirect_symbol): Merge rel_count.
(ppc64_elf_check_relocs): Init rel_count for global and local syms.
(dec_dynrel_count): Change r_info param to reloc pointer. Update
all callers. Handle decrementing rel_count.
(allocate_got): Don't allocate space for relative relocs when
enable_dt_relr.
(allocate_dynrelocs): Likewise.
(ppc64_elf_size_dynamic_sections): Likewise. Handle srelrdyn.
(ppc_build_one_stub): Don't emit relative relocs on .branch_lt.
(compare_relr_address, append_relr_off): New functions.
(got_and_plt_relr_for_local_syms, got_and_plt_relr): Likewise.
(ppc64_elf_size_stubs): Size .relr.syn.
(ppc64_elf_build_stubs): Emit .relr.dyn.
(build_global_entry_stubs_and_plt): Don't output relative relocs
when enable_dt_relr.
(write_plt_relocs_for_local_syms): Likewise.
(ppc64_elf_relocate_section): Likewise.
binutils/
* testsuite/lib/binutils-common.exp (supports_dt_relr): Add
powerpc64.
ld/
* emulparams/elf64ppc.sh: Source dt-relr.sh.
* testsuite/ld-elf/dt-relr-2b.d: Adjust for powerpc.
* testsuite/ld-elf/dt-relr-2c.d: Likewise.
* testsuite/ld-elf/dt-relr-2d.d: Likewise.
* testsuite/ld-elf/dt-relr-2e.d: Likewise.
As pre-approved by Alan in
https://sourceware.org/pipermail/binutils/2021-September/118019.html
and I believe people have run into getting testsuite failures for
test-environments with "long" directory names, at least once more
since that time. Enough. I grepped the gas, binutils and ld
testsuites for "CU:" to catch target-specific occurrences, but I
noticed none. I chose to remove "CU:" on the objdump tests instead of
changing options to get the wide format, so as to keep the name of the
test consistent with actual options; but added it to the readelf
options for the gas test as I believe the "CU:" format is preferable.
Tested for cris-elf and native x86_64-pc-linux-gnu.
binutils:
* dwarf.c (display_debug_lines_decoded): Don't check the
string length of the directory, instead emit the "CU: dir/name"
format only if wide output is requested.
* testsuite/binutils-all/dw5.W, testsuite/binutils-all/objdump.WL:
Adjust accordingly.
gas:
* testsuite/gas/elf/dwarf-5-loc0.d: Add -W to readelf options.
