forked from Imagelibrary/rtems
140 lines
4.8 KiB
C
140 lines
4.8 KiB
C
/**
|
|
* @file
|
|
*
|
|
* This file manages the benchmark timer used by the RTEMS Timing Test Suite.
|
|
* Each measured time period is demarcated by calls to
|
|
* benchmark_timer_initialize() and benchmark_timer_read().
|
|
* benchmark_timer_read() usually returns the number of microseconds
|
|
* since benchmark_timer_initialize() exitted.
|
|
*
|
|
* These functions are prototyped in rtems/btimer.h and
|
|
* must be implemented as part of the BSP.
|
|
*
|
|
* This port does not allow the application to select which timer on the
|
|
* MVME167 to use for the timer, nor does it allow the application to
|
|
* configure the timer. The timer uses the VMEchip2 Tick Timer #1. This timer
|
|
* is distinct from the clock, which uses Tick Timer #2 in the VMEchip2.
|
|
*
|
|
* All page references are to the MVME166/MVME167/MVME187 Single Board
|
|
* Computer Programmer's Reference Guide (MVME187PG/D2) with the April 1993
|
|
* supplements/addenda (MVME187PG/D2A1).
|
|
*/
|
|
|
|
/*
|
|
* COPYRIGHT (c) 1989-1999.
|
|
* On-Line Applications Research Corporation (OAR).
|
|
*
|
|
* The license and distribution terms for this file may be
|
|
* found in the file LICENSE in this distribution or at
|
|
* http://www.rtems.org/license/LICENSE.
|
|
*
|
|
* Modifications of respective RTEMS file:
|
|
* Copyright (c) 1998, National Research Council of Canada
|
|
*/
|
|
|
|
#include <rtems.h>
|
|
#include <rtems/btimer.h>
|
|
#include <bsp.h>
|
|
|
|
/* Periodic tick interval */
|
|
#define TICK_INTERVAL 10000UL /* T1's countdown constant (10 ms) */
|
|
#define TIMER_INT_LEVEL 6 /* T1's interrupt level */
|
|
#define TIMER_VECTOR (VBR0 * 0x10 + 0x8) /* T1 is vector $X8 (p. 2-71)*/
|
|
|
|
/* Number of interrupts since timer was re-initialized */
|
|
uint32_t Ttimer_val;
|
|
|
|
/*
|
|
* Set to true to return raw value. Normally zero. Depends on being allocated
|
|
* in the .bss section and on that section being explicitly zeroed at boot
|
|
* time.
|
|
*/
|
|
bool benchmark_timer_find_average_overhead;
|
|
|
|
rtems_isr timerisr(rtems_vector_number);
|
|
|
|
/*
|
|
* This routine initializes the Tick Timer 1 on the MVME167 board.
|
|
*
|
|
* Input parameters: NONE
|
|
*
|
|
* Output parameters: NONE
|
|
*
|
|
* NOTE: This routine may not work if the optimizer is enabled for some
|
|
* compilers. The multiple writes may be optimized away.
|
|
*
|
|
* It is important that the timer start/stop overhead be
|
|
* determined when porting or modifying this code.
|
|
*
|
|
* THE VMECHIP2 PRESCALER REGISTER IS ASSUMED TO BE SET!
|
|
* The prescaler is used by all VMEchip2 timers, including the VMEbus grant
|
|
* timeout counter, the DMAC time off timer, the DMAC timer on timer, and the
|
|
* VMEbus global timeout timer. The prescaler value is normally set by the
|
|
* boot ROM to provide a 1 MHz clock to the timers. For a 25 MHz MVME167, the
|
|
* prescaler value should be 0xE7 (page 2-63).
|
|
*/
|
|
void benchmark_timer_initialize(void)
|
|
{
|
|
(void) set_vector( timerisr, TIMER_VECTOR, 0 );
|
|
|
|
Ttimer_val = 0; /* clear timer ISR count */
|
|
lcsr->intr_ena &= 0xFEFFFFFF; /* disable tick timer 1 interrupt */
|
|
lcsr->intr_clear |= 0x01000000; /* clear tick timer 1 interrupt */
|
|
lcsr->intr_level[0] = /* set int level */
|
|
(lcsr->intr_level[0] & 0xFFFFFFF0) | TIMER_INT_LEVEL;
|
|
lcsr->timer_cmp_1 = TICK_INTERVAL; /* period in compare register */
|
|
lcsr->timer_cnt_1 = 0; /* clear tick timer 1 counter */
|
|
lcsr->board_ctl |= 7; /* start tick timer 1, reset-on-compare, */
|
|
/* and clear overflow counter */
|
|
|
|
lcsr->intr_ena |= 0x01000000; /* enable tick timer 1 interrupt */
|
|
lcsr->vector_base |= MASK_INT; /* unmask VMEchip2 interrupts */
|
|
}
|
|
|
|
#define AVG_OVERHEAD 3UL /* It typically takes 3.0 microseconds */
|
|
/* (3 countdowns) to start/stop the timer. */
|
|
#define LEAST_VALID 3UL /* Don't trust a value lower than this */
|
|
|
|
/*
|
|
* This routine reads the Tick Timer 1 on the MVME167 board.
|
|
*
|
|
* Input parameters: NONE
|
|
*
|
|
* Output parameters: time in microseconds
|
|
*
|
|
* AVG_OVEREHAD is the overhead for starting and stopping the timer. It
|
|
* is usually deducted from the number returned.
|
|
*
|
|
* LEAST_VALID is the lowest number this routine should trust. Numbers
|
|
* below this are "noise" and zero is returned.
|
|
*/
|
|
benchmark_timer_t benchmark_timer_read(void)
|
|
{
|
|
uint32_t total;
|
|
|
|
total = (Ttimer_val * TICK_INTERVAL) + lcsr->timer_cnt_1;
|
|
|
|
if ( benchmark_timer_find_average_overhead )
|
|
return total; /* in one microsecond units */
|
|
|
|
if ( total < LEAST_VALID )
|
|
return 0; /* below timer resolution */
|
|
|
|
return total - AVG_OVERHEAD;
|
|
}
|
|
|
|
/*
|
|
* This routine sets the benchmark_timer_find_average_overhead flag in this
|
|
* module.
|
|
*
|
|
* Input parameters: NONE
|
|
*
|
|
* Output parameters: time in microseconds
|
|
*/
|
|
void benchmark_timer_disable_subtracting_average_overhead(
|
|
bool find_flag
|
|
)
|
|
{
|
|
benchmark_timer_find_average_overhead = find_flag;
|
|
}
|