forked from Imagelibrary/rtems
50539ba881
This support code is necessary for many Xilinx-provided bare metal device drivers supported on ARM, AArch64, and MicroBlaze platforms. Support for all of these architectures is kept under bsps/include due to multiple architecture variants being supported which requires complex logic in the build system. The imported files are and should be able to remain unmodified. Import information is kept in bsps/shared/xil/VERSION.
523 lines
19 KiB
C
523 lines
19 KiB
C
/******************************************************************************
|
|
* Copyright (c) 2002 - 2021 Xilinx, Inc. All rights reserved.
|
|
* SPDX-License-Identifier: MIT
|
|
******************************************************************************/
|
|
|
|
/*****************************************************************************/
|
|
/**
|
|
*
|
|
* @file xstatus.h
|
|
*
|
|
* @addtogroup common_status_codes Xilinx software status codes
|
|
*
|
|
* The xstatus.h file contains the Xilinx software status codes.These codes are
|
|
* used throughout the Xilinx device drivers.
|
|
*
|
|
* @{
|
|
******************************************************************************/
|
|
|
|
/**
|
|
*@cond nocomments
|
|
*/
|
|
|
|
#ifndef XSTATUS_H /* prevent circular inclusions */
|
|
#define XSTATUS_H /* by using protection macros */
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/***************************** Include Files *********************************/
|
|
|
|
#include "xil_types.h"
|
|
#include "xil_assert.h"
|
|
|
|
/************************** Constant Definitions *****************************/
|
|
|
|
/*********************** Common statuses 0 - 500 *****************************/
|
|
/**
|
|
@name Common Status Codes for All Device Drivers
|
|
@{
|
|
*/
|
|
#define XST_SUCCESS 0L
|
|
#define XST_FAILURE 1L
|
|
#define XST_DEVICE_NOT_FOUND 2L
|
|
#define XST_DEVICE_BLOCK_NOT_FOUND 3L
|
|
#define XST_INVALID_VERSION 4L
|
|
#define XST_DEVICE_IS_STARTED 5L
|
|
#define XST_DEVICE_IS_STOPPED 6L
|
|
#define XST_FIFO_ERROR 7L /*!< An error occurred during an
|
|
operation with a FIFO such as
|
|
an underrun or overrun, this
|
|
error requires the device to
|
|
be reset */
|
|
#define XST_RESET_ERROR 8L /*!< An error occurred which requires
|
|
the device to be reset */
|
|
#define XST_DMA_ERROR 9L /*!< A DMA error occurred, this error
|
|
typically requires the device
|
|
using the DMA to be reset */
|
|
#define XST_NOT_POLLED 10L /*!< The device is not configured for
|
|
polled mode operation */
|
|
#define XST_FIFO_NO_ROOM 11L /*!< A FIFO did not have room to put
|
|
the specified data into */
|
|
#define XST_BUFFER_TOO_SMALL 12L /*!< The buffer is not large enough
|
|
to hold the expected data */
|
|
#define XST_NO_DATA 13L /*!< There was no data available */
|
|
#define XST_REGISTER_ERROR 14L /*!< A register did not contain the
|
|
expected value */
|
|
#define XST_INVALID_PARAM 15L /*!< An invalid parameter was passed
|
|
into the function */
|
|
#define XST_NOT_SGDMA 16L /*!< The device is not configured for
|
|
scatter-gather DMA operation */
|
|
#define XST_LOOPBACK_ERROR 17L /*!< A loopback test failed */
|
|
#define XST_NO_CALLBACK 18L /*!< A callback has not yet been
|
|
registered */
|
|
#define XST_NO_FEATURE 19L /*!< Device is not configured with
|
|
the requested feature */
|
|
#define XST_NOT_INTERRUPT 20L /*!< Device is not configured for
|
|
interrupt mode operation */
|
|
#define XST_DEVICE_BUSY 21L /*!< Device is busy */
|
|
#define XST_ERROR_COUNT_MAX 22L /*!< The error counters of a device
|
|
have maxed out */
|
|
#define XST_IS_STARTED 23L /*!< Used when part of device is
|
|
already started i.e.
|
|
sub channel */
|
|
#define XST_IS_STOPPED 24L /*!< Used when part of device is
|
|
already stopped i.e.
|
|
sub channel */
|
|
#define XST_DATA_LOST 26L /*!< Driver defined error */
|
|
#define XST_RECV_ERROR 27L /*!< Generic receive error */
|
|
#define XST_SEND_ERROR 28L /*!< Generic transmit error */
|
|
#define XST_NOT_ENABLED 29L /*!< A requested service is not
|
|
available because it has not
|
|
been enabled */
|
|
#define XST_NO_ACCESS 30L /* Generic access error */
|
|
#define XST_TIMEOUT 31L /*!< Event timeout occurred */
|
|
|
|
/** @} */
|
|
/***************** Utility Component statuses 401 - 500 *********************/
|
|
/**
|
|
@name Utility Component Status Codes 401 - 500
|
|
@{
|
|
*/
|
|
#define XST_MEMTEST_FAILED 401L /*!< Memory test failed */
|
|
|
|
/** @} */
|
|
/***************** Common Components statuses 501 - 1000 *********************/
|
|
/**
|
|
@name Packet Fifo Status Codes 501 - 510
|
|
@{
|
|
*/
|
|
/********************* Packet Fifo statuses 501 - 510 ************************/
|
|
|
|
#define XST_PFIFO_LACK_OF_DATA 501L /*!< Not enough data in FIFO */
|
|
#define XST_PFIFO_NO_ROOM 502L /*!< Not enough room in FIFO */
|
|
#define XST_PFIFO_BAD_REG_VALUE 503L /*!< Self test, a register value
|
|
was invalid after reset */
|
|
#define XST_PFIFO_ERROR 504L /*!< Generic packet FIFO error */
|
|
#define XST_PFIFO_DEADLOCK 505L /*!< Packet FIFO is reporting
|
|
* empty and full simultaneously
|
|
*/
|
|
/** @} */
|
|
/**
|
|
@name DMA Status Codes 511 - 530
|
|
@{
|
|
*/
|
|
/************************** DMA statuses 511 - 530 ***************************/
|
|
|
|
#define XST_DMA_TRANSFER_ERROR 511L /*!< Self test, DMA transfer
|
|
failed */
|
|
#define XST_DMA_RESET_REGISTER_ERROR 512L /*!< Self test, a register value
|
|
was invalid after reset */
|
|
#define XST_DMA_SG_LIST_EMPTY 513L /*!< Scatter gather list contains
|
|
no buffer descriptors ready
|
|
to be processed */
|
|
#define XST_DMA_SG_IS_STARTED 514L /*!< Scatter gather not stopped */
|
|
#define XST_DMA_SG_IS_STOPPED 515L /*!< Scatter gather not running */
|
|
#define XST_DMA_SG_LIST_FULL 517L /*!< All the buffer descriptors of
|
|
the scatter gather list are
|
|
being used */
|
|
#define XST_DMA_SG_BD_LOCKED 518L /*!< The scatter gather buffer
|
|
descriptor which is to be
|
|
copied over in the scatter
|
|
list is locked */
|
|
#define XST_DMA_SG_NOTHING_TO_COMMIT 519L /*!< No buffer descriptors have been
|
|
put into the scatter gather
|
|
list to be committed */
|
|
#define XST_DMA_SG_COUNT_EXCEEDED 521L /*!< The packet count threshold
|
|
specified was larger than the
|
|
total # of buffer descriptors
|
|
in the scatter gather list */
|
|
#define XST_DMA_SG_LIST_EXISTS 522L /*!< The scatter gather list has
|
|
already been created */
|
|
#define XST_DMA_SG_NO_LIST 523L /*!< No scatter gather list has
|
|
been created */
|
|
#define XST_DMA_SG_BD_NOT_COMMITTED 524L /*!< The buffer descriptor which was
|
|
being started was not committed
|
|
to the list */
|
|
#define XST_DMA_SG_NO_DATA 525L /*!< The buffer descriptor to start
|
|
has already been used by the
|
|
hardware so it can't be reused
|
|
*/
|
|
#define XST_DMA_SG_LIST_ERROR 526L /*!< General purpose list access
|
|
error */
|
|
#define XST_DMA_BD_ERROR 527L /*!< General buffer descriptor
|
|
error */
|
|
/** @} */
|
|
/**
|
|
@name IPIF Status Codes Codes 531 - 550
|
|
@{
|
|
*/
|
|
/************************** IPIF statuses 531 - 550 ***************************/
|
|
|
|
#define XST_IPIF_REG_WIDTH_ERROR 531L /*!< An invalid register width
|
|
was passed into the function */
|
|
#define XST_IPIF_RESET_REGISTER_ERROR 532L /*!< The value of a register at
|
|
reset was not valid */
|
|
#define XST_IPIF_DEVICE_STATUS_ERROR 533L /*!< A write to the device interrupt
|
|
status register did not read
|
|
back correctly */
|
|
#define XST_IPIF_DEVICE_ACK_ERROR 534L /*!< The device interrupt status
|
|
register did not reset when
|
|
acked */
|
|
#define XST_IPIF_DEVICE_ENABLE_ERROR 535L /*!< The device interrupt enable
|
|
register was not updated when
|
|
other registers changed */
|
|
#define XST_IPIF_IP_STATUS_ERROR 536L /*!< A write to the IP interrupt
|
|
status register did not read
|
|
back correctly */
|
|
#define XST_IPIF_IP_ACK_ERROR 537L /*!< The IP interrupt status register
|
|
did not reset when acked */
|
|
#define XST_IPIF_IP_ENABLE_ERROR 538L /*!< IP interrupt enable register was
|
|
not updated correctly when other
|
|
registers changed */
|
|
#define XST_IPIF_DEVICE_PENDING_ERROR 539L /*!< The device interrupt pending
|
|
register did not indicate the
|
|
expected value */
|
|
#define XST_IPIF_DEVICE_ID_ERROR 540L /*!< The device interrupt ID register
|
|
did not indicate the expected
|
|
value */
|
|
#define XST_IPIF_ERROR 541L /*!< Generic ipif error */
|
|
/** @} */
|
|
|
|
/****************** Device specific statuses 1001 - 4095 *********************/
|
|
/**
|
|
@name Ethernet Status Codes 1001 - 1050
|
|
@{
|
|
*/
|
|
/********************* Ethernet statuses 1001 - 1050 *************************/
|
|
|
|
#define XST_EMAC_MEMORY_SIZE_ERROR 1001L /*!< Memory space is not big enough
|
|
* to hold the minimum number of
|
|
* buffers or descriptors */
|
|
#define XST_EMAC_MEMORY_ALLOC_ERROR 1002L /*!< Memory allocation failed */
|
|
#define XST_EMAC_MII_READ_ERROR 1003L /*!< MII read error */
|
|
#define XST_EMAC_MII_BUSY 1004L /*!< An MII operation is in progress */
|
|
#define XST_EMAC_OUT_OF_BUFFERS 1005L /*!< Driver is out of buffers */
|
|
#define XST_EMAC_PARSE_ERROR 1006L /*!< Invalid driver init string */
|
|
#define XST_EMAC_COLLISION_ERROR 1007L /*!< Excess deferral or late
|
|
* collision on polled send */
|
|
/** @} */
|
|
/**
|
|
@name UART Status Codes 1051 - 1075
|
|
@{
|
|
*/
|
|
/*********************** UART statuses 1051 - 1075 ***************************/
|
|
#define XST_UART
|
|
|
|
#define XST_UART_INIT_ERROR 1051L
|
|
#define XST_UART_START_ERROR 1052L
|
|
#define XST_UART_CONFIG_ERROR 1053L
|
|
#define XST_UART_TEST_FAIL 1054L
|
|
#define XST_UART_BAUD_ERROR 1055L
|
|
#define XST_UART_BAUD_RANGE 1056L
|
|
|
|
/** @} */
|
|
/**
|
|
@name IIC Status Codes 1076 - 1100
|
|
@{
|
|
*/
|
|
/************************ IIC statuses 1076 - 1100 ***************************/
|
|
|
|
#define XST_IIC_SELFTEST_FAILED 1076 /*!< self test failed */
|
|
#define XST_IIC_BUS_BUSY 1077 /*!< bus found busy */
|
|
#define XST_IIC_GENERAL_CALL_ADDRESS 1078 /*!< mastersend attempted with */
|
|
/* general call address */
|
|
#define XST_IIC_STAND_REG_RESET_ERROR 1079 /*!< A non parameterizable reg */
|
|
/* value after reset not valid */
|
|
#define XST_IIC_TX_FIFO_REG_RESET_ERROR 1080 /*!< Tx fifo included in design */
|
|
/* value after reset not valid */
|
|
#define XST_IIC_RX_FIFO_REG_RESET_ERROR 1081 /*!< Rx fifo included in design */
|
|
/* value after reset not valid */
|
|
#define XST_IIC_TBA_REG_RESET_ERROR 1082 /*!< 10 bit addr incl in design */
|
|
/* value after reset not valid */
|
|
#define XST_IIC_CR_READBACK_ERROR 1083 /*!< Read of the control register */
|
|
/* didn't return value written */
|
|
#define XST_IIC_DTR_READBACK_ERROR 1084 /*!< Read of the data Tx reg */
|
|
/* didn't return value written */
|
|
#define XST_IIC_DRR_READBACK_ERROR 1085 /*!< Read of the data Receive reg */
|
|
/* didn't return value written */
|
|
#define XST_IIC_ADR_READBACK_ERROR 1086 /*!< Read of the data Tx reg */
|
|
/* didn't return value written */
|
|
#define XST_IIC_TBA_READBACK_ERROR 1087 /*!< Read of the 10 bit addr reg */
|
|
/* didn't return written value */
|
|
#define XST_IIC_NOT_SLAVE 1088 /*!< The device isn't a slave */
|
|
#define XST_IIC_ARB_LOST 1089 /*!< Arbitration lost for master */
|
|
/** @} */
|
|
/**
|
|
@name ATMC Status Codes 1101 - 1125
|
|
@{
|
|
*/
|
|
/*********************** ATMC statuses 1101 - 1125 ***************************/
|
|
|
|
#define XST_ATMC_ERROR_COUNT_MAX 1101L /*!< the error counters in the ATM
|
|
controller hit the max value
|
|
which requires the statistics
|
|
to be cleared */
|
|
/** @} */
|
|
/**
|
|
@name Flash Status Codes 1126 - 1150
|
|
@{
|
|
*/
|
|
/*********************** Flash statuses 1126 - 1150 **************************/
|
|
|
|
#define XST_FLASH_BUSY 1126L /*!< Flash is erasing or programming
|
|
*/
|
|
#define XST_FLASH_READY 1127L /*!< Flash is ready for commands */
|
|
#define XST_FLASH_ERROR 1128L /*!< Flash had detected an internal
|
|
error. Use XFlash_DeviceControl
|
|
to retrieve device specific codes
|
|
*/
|
|
#define XST_FLASH_ERASE_SUSPENDED 1129L /*!< Flash is in suspended erase state
|
|
*/
|
|
#define XST_FLASH_WRITE_SUSPENDED 1130L /*!< Flash is in suspended write state
|
|
*/
|
|
#define XST_FLASH_PART_NOT_SUPPORTED 1131L /*!< Flash type not supported by
|
|
driver */
|
|
#define XST_FLASH_NOT_SUPPORTED 1132L /*!< Operation not supported */
|
|
#define XST_FLASH_TOO_MANY_REGIONS 1133L /*!< Too many erase regions */
|
|
#define XST_FLASH_TIMEOUT_ERROR 1134L /*!< Programming or erase operation
|
|
aborted due to a timeout */
|
|
#define XST_FLASH_ADDRESS_ERROR 1135L /*!< Accessed flash outside its
|
|
addressible range */
|
|
#define XST_FLASH_ALIGNMENT_ERROR 1136L /*!< Write alignment error */
|
|
#define XST_FLASH_BLOCKING_CALL_ERROR 1137L /*!< Couldn't return immediately from
|
|
write/erase function with
|
|
XFL_NON_BLOCKING_WRITE/ERASE
|
|
option cleared */
|
|
#define XST_FLASH_CFI_QUERY_ERROR 1138L /*!< Failed to query the device */
|
|
/** @} */
|
|
/**
|
|
@name SPI Status Codes 1151 - 1175
|
|
@{
|
|
*/
|
|
/*********************** SPI statuses 1151 - 1175 ****************************/
|
|
|
|
#define XST_SPI_MODE_FAULT 1151 /*!< master was selected as slave */
|
|
#define XST_SPI_TRANSFER_DONE 1152 /*!< data transfer is complete */
|
|
#define XST_SPI_TRANSMIT_UNDERRUN 1153 /*!< slave underruns transmit register */
|
|
#define XST_SPI_RECEIVE_OVERRUN 1154 /*!< device overruns receive register */
|
|
#define XST_SPI_NO_SLAVE 1155 /*!< no slave has been selected yet */
|
|
#define XST_SPI_TOO_MANY_SLAVES 1156 /*!< more than one slave is being
|
|
* selected */
|
|
#define XST_SPI_NOT_MASTER 1157 /*!< operation is valid only as master */
|
|
#define XST_SPI_SLAVE_ONLY 1158 /*!< device is configured as slave-only
|
|
*/
|
|
#define XST_SPI_SLAVE_MODE_FAULT 1159 /*!< slave was selected while disabled */
|
|
#define XST_SPI_SLAVE_MODE 1160 /*!< device has been addressed as slave */
|
|
#define XST_SPI_RECEIVE_NOT_EMPTY 1161 /*!< device received data in slave mode */
|
|
|
|
#define XST_SPI_COMMAND_ERROR 1162 /*!< unrecognised command - qspi only */
|
|
#define XST_SPI_POLL_DONE 1163 /*!< controller completed polling the
|
|
device for status */
|
|
/** @} */
|
|
/**
|
|
@name OPB Arbiter Status Codes 1176 - 1200
|
|
@{
|
|
*/
|
|
/********************** OPB Arbiter statuses 1176 - 1200 *********************/
|
|
|
|
#define XST_OPBARB_INVALID_PRIORITY 1176 /*!< the priority registers have either
|
|
* one master assigned to two or more
|
|
* priorities, or one master not
|
|
* assigned to any priority
|
|
*/
|
|
#define XST_OPBARB_NOT_SUSPENDED 1177 /*!< an attempt was made to modify the
|
|
* priority levels without first
|
|
* suspending the use of priority
|
|
* levels
|
|
*/
|
|
#define XST_OPBARB_PARK_NOT_ENABLED 1178 /*!< bus parking by id was enabled but
|
|
* bus parking was not enabled
|
|
*/
|
|
#define XST_OPBARB_NOT_FIXED_PRIORITY 1179 /*!< the arbiter must be in fixed
|
|
* priority mode to allow the
|
|
* priorities to be changed
|
|
*/
|
|
/** @} */
|
|
/**
|
|
@name INTC Status Codes 1201 - 1225
|
|
@{
|
|
*/
|
|
/************************ Intc statuses 1201 - 1225 **************************/
|
|
|
|
#define XST_INTC_FAIL_SELFTEST 1201 /*!< self test failed */
|
|
#define XST_INTC_CONNECT_ERROR 1202 /*!< interrupt already in use */
|
|
/** @} */
|
|
/**
|
|
@name TmrCtr Status Codes 1226 - 1250
|
|
@{
|
|
*/
|
|
/********************** TmrCtr statuses 1226 - 1250 **************************/
|
|
|
|
#define XST_TMRCTR_TIMER_FAILED 1226 /*!< self test failed */
|
|
/** @} */
|
|
/**
|
|
@name WdtTb Status Codes 1251 - 1275
|
|
@{
|
|
*/
|
|
/********************** WdtTb statuses 1251 - 1275 ***************************/
|
|
|
|
#define XST_WDTTB_TIMER_FAILED 1251L
|
|
/** @} */
|
|
/**
|
|
@name PlbArb status Codes 1276 - 1300
|
|
@{
|
|
*/
|
|
/********************** PlbArb statuses 1276 - 1300 **************************/
|
|
|
|
#define XST_PLBARB_FAIL_SELFTEST 1276L
|
|
/** @} */
|
|
/**
|
|
@name Plb2Opb Status Codes 1301 - 1325
|
|
@{
|
|
*/
|
|
/********************** Plb2Opb statuses 1301 - 1325 *************************/
|
|
|
|
#define XST_PLB2OPB_FAIL_SELFTEST 1301L
|
|
/** @} */
|
|
/**
|
|
@name Opb2Plb Status 1326 - 1350
|
|
@{
|
|
*/
|
|
/********************** Opb2Plb statuses 1326 - 1350 *************************/
|
|
|
|
#define XST_OPB2PLB_FAIL_SELFTEST 1326L
|
|
/** @} */
|
|
/**
|
|
@name SysAce Status Codes 1351 - 1360
|
|
@{
|
|
*/
|
|
/********************** SysAce statuses 1351 - 1360 **************************/
|
|
|
|
#define XST_SYSACE_NO_LOCK 1351L /*!< No MPU lock has been granted */
|
|
/** @} */
|
|
/**
|
|
@name PCI Bridge Status Codes 1361 - 1375
|
|
@{
|
|
*/
|
|
/********************** PCI Bridge statuses 1361 - 1375 **********************/
|
|
|
|
#define XST_PCI_INVALID_ADDRESS 1361L
|
|
/** @} */
|
|
/**
|
|
@name FlexRay Constants 1400 - 1409
|
|
@{
|
|
*/
|
|
/********************** FlexRay constants 1400 - 1409 *************************/
|
|
|
|
#define XST_FR_TX_ERROR 1400
|
|
#define XST_FR_TX_BUSY 1401
|
|
#define XST_FR_BUF_LOCKED 1402
|
|
#define XST_FR_NO_BUF 1403
|
|
/** @} */
|
|
/**
|
|
@name USB constants 1410 - 1420
|
|
@{
|
|
*/
|
|
/****************** USB constants 1410 - 1420 *******************************/
|
|
|
|
#define XST_USB_ALREADY_CONFIGURED 1410
|
|
#define XST_USB_BUF_ALIGN_ERROR 1411
|
|
#define XST_USB_NO_DESC_AVAILABLE 1412
|
|
#define XST_USB_BUF_TOO_BIG 1413
|
|
#define XST_USB_NO_BUF 1414
|
|
/** @} */
|
|
/**
|
|
@name HWICAP constants 1421 - 1429
|
|
@{
|
|
*/
|
|
/****************** HWICAP constants 1421 - 1429 *****************************/
|
|
|
|
#define XST_HWICAP_WRITE_DONE 1421
|
|
|
|
/** @} */
|
|
/**
|
|
@name AXI VDMA constants 1430 - 1440
|
|
@{
|
|
*/
|
|
/****************** AXI VDMA constants 1430 - 1440 *****************************/
|
|
|
|
#define XST_VDMA_MISMATCH_ERROR 1430
|
|
/** @} */
|
|
/**
|
|
@name NAND Flash Status Codes 1441 - 1459
|
|
@{
|
|
*/
|
|
/*********************** NAND Flash statuses 1441 - 1459 *********************/
|
|
|
|
#define XST_NAND_BUSY 1441L /*!< Flash is erasing or
|
|
* programming
|
|
*/
|
|
#define XST_NAND_READY 1442L /*!< Flash is ready for commands
|
|
*/
|
|
#define XST_NAND_ERROR 1443L /*!< Flash had detected an
|
|
* internal error.
|
|
*/
|
|
#define XST_NAND_PART_NOT_SUPPORTED 1444L /*!< Flash type not supported by
|
|
* driver
|
|
*/
|
|
#define XST_NAND_OPT_NOT_SUPPORTED 1445L /*!< Operation not supported
|
|
*/
|
|
#define XST_NAND_TIMEOUT_ERROR 1446L /*!< Programming or erase
|
|
* operation aborted due to a
|
|
* timeout
|
|
*/
|
|
#define XST_NAND_ADDRESS_ERROR 1447L /*!< Accessed flash outside its
|
|
* addressible range
|
|
*/
|
|
#define XST_NAND_ALIGNMENT_ERROR 1448L /*!< Write alignment error
|
|
*/
|
|
#define XST_NAND_PARAM_PAGE_ERROR 1449L /*!< Failed to read parameter
|
|
* page of the device
|
|
*/
|
|
#define XST_NAND_CACHE_ERROR 1450L /*!< Flash page buffer error
|
|
*/
|
|
|
|
#define XST_NAND_WRITE_PROTECTED 1451L /*!< Flash is write protected
|
|
*/
|
|
/** @} */
|
|
|
|
/**************************** Type Definitions *******************************/
|
|
|
|
typedef s32 XStatus;
|
|
|
|
/***************** Macros (Inline Functions) Definitions *********************/
|
|
|
|
|
|
/************************** Function Prototypes ******************************/
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* end of protection macro */
|
|
|
|
/**
|
|
*@endcond
|
|
*/
|
|
|
|
/**
|
|
* @} End of "addtogroup common_status_codes".
|
|
*/
|