This BSP supports a custom STM32U5 based board. It uses a similar
structure like the existing STM32H7 BSP and therefore should be well
adaptable to other boards.
Co-authored-by: Christian Mauderer <christian.mauderer@embedded-brains.de>
This removes the headers imported from the embeddedsw repository in
favor of a much thinner shim. This also removes the complicated build
system configuration necessary to support use of these headers. The
primary reason for removal is that certain external Xilinx libraries
also require use of these headers and this causes version mismatches and
header conflicts that can be avoided.
This adds support for the 6 SPI interfaces on the STM32H7 series chips
with an initial example for the stm32h750b discovery kit development
board. Configuration is similar to existing peripherals. Chip select
lines are software-controlled since the SPI peripheral only supports a
single hardware-controlled chip select line. This implementation does
not use interrupts.
This adds error reporting for ZynqMP including L1 and L2 cache, on-chip
memory (OCM) error correcting code (ECC), and DDR ECC. OCM ECC supports
fault injection from within RTEMS. DDR ECC technically supports fault
injection as well, but requires that the program injecting faults
operate exclusively outside of DDR. The AArch64 port is not currently
capable of operating exclusively in OCM due to size constraints and
would need to be booted via JTAG or via a non-relocating u-boot to
accomplish this.
Add directives to get and set the priority of an interrupt vector.
Implement the directives for the following BSP families:
* arm/lpc24xx
* arm/lpc32xx
* powerpc/mpc55xxevb
* powerpc/qoriq
Implement the directives for the following interrupt controllers:
* GICv2 and GICv3 (arm and aarch64)
* NVIC (arm)
* PLIC (riscv)
Update #5002.
Move declarations of bsp_interrupt_get_affinity() and
bsp_interrupt_set_affinity() to <bsp/irq-generic.h>. Canonicalize the
<bsp/irq.h> includes.
Implement bsp_interrupt_get_affinity() and bsp_interrupt_set_affinity() only if
needed (usually RTEMS_SMP).
Provide stub implementations for i386 to fix build errors.
In SMP configurations, there may be no software interrupt handler
installed when the software interrupt is processed. Add the new
interrupt handler dispatch variant
bsp_interrupt_handler_dispatch_unlikely() for this special case.
Added support for Cobham Gaisler NOEL-V systems. The NOEL-V support
is implemented as a riscv BSP. Both 32-bit and 64-bit processor
systems are supported. Cobham Gaisler's NOEL-V RISC-V processor IP
is described here:
https://www.gaisler.com/NOELV
Compatible with the following NOEL-V FPGA example design ranges
available from Cobham Gaisler. Follow the links for free
bit-streams, DTS/DTB, user's manuals and quick-start guides:
- NOEL-ARTYA7-EX (https://www.gaisler.com/NOEL-ARTYA7)
- NOEL-PF-EX (https://www.gaisler.com/NOEL-PF)
- NOEL-XCKU-EX (https://www.gaisler.com/NOEL-XCKU)
Uses the shared GRLIB APBUART console driver "apbuart_termios.c".
APBUART devices are probed using device tree.
Closes#4225.
- Support DDRMC0 region 0 up to 2G in size
- Support DDRMC0 region 1 with DDR memory greater than 2G
up to the DDRMC0 max amount
- Extend the heap with region 1's memory
Closes#4684
This alters the AArch64 page table generation and mapping code and MMU
configuration to use page table level 0 in addition to levels 1, 2, and
3. This allows the mapping of up to 48 bits of memory space and is the
maximum that can be mapped without relying on additional processor
extensions. Mappings are restricted based on the number of physical
address bits that the CPU supports.
Rename LEON3_FATAL_INVALID_CACHE_CONFIG_MAIN_PROCESSOR in
LEON3_FATAL_INVALID_CACHE_CONFIG_BOOT_PROCESSOR since the term
"boot processor" is used elsewhere in the code base.
Do not return a status code in bsp_interrupt_facility_initialize() since this
leads to unreachable code in bsp_interrupt_initialize(). Use RTEMS_DEBUG
assertions in bsp_interrupt_facility_initialize() if necessary.
Add rtems_interrupt_entry_remove(). Split up irq-generic.c into several files.
In particular, place all functions which use dynamic memory into their own
file.
Add optional macros to let the BSP customize the vector installation after
installing the first entry and the vector removal before removing the last
entry:
* bsp_interrupt_vector_install()
* bsp_interrupt_vector_remove()
Use these new customization options in the m68k/genmcf548x BSP so re-use the
generic interrupt controller support.
Update #3269.
Return RTEMS_INCORRECT_STATE instead of RTEMS_INTERNAL_ERROR in case the
interrupt support is not initialized. This is similar to
rtems_timer_server_fire_after() for example.
Update #3269.
Add rtems_interrupt_raise_on() and rtems_interrupt_clear().
Add a default implementation which just returns RTEMS_UNSATISFIED for
valid parameters.
Update #3269.
Add bsp_interrupt_handler_dispatch_unchecked() as an alternative to
bsp_interrupt_handler_dispatch(). It may be used if the caller can ensure that
the vector number is valid.
Change the default value of BSP_INTERRUPT_VECTOR_COUNT so that no interrupt
vectors are supported and all related directives return RTEMS_INVALID_ID.
Update #3269.
