2009-06-18 Fernando Nicodemos <fgnicodemos@terra.com.br>

* Makefile.am, configure.ac, console/uarts.c: Add console device that
	uses MicroMonitor to do actual input and output. This driver should
	work on any board that uses MicroMonitor.

c/src/lib/libbsp/arm/csb337/ChangeLog

@@ -1,3 +1,9 @@
+2009-06-18	Fernando Nicodemos <fgnicodemos@terra.com.br>
+
+	* Makefile.am, configure.ac, console/uarts.c: Add console device that
+	uses MicroMonitor to do actual input and output. This driver should
+	work on any board that uses MicroMonitor.
+
 2009-06-18	Joel Sherrill <joel.sherrill@OARcorp.com>
 
 	* startup/linkcmds, startup/linkcmds.csb637: Move .init section from

c/src/lib/libbsp/arm/csb337/Makefile.am

@@ -61,7 +61,7 @@ libbsp_a_SOURCES += ../shared/abort/abort.c
 # umon
 libbsp_a_SOURCES += ../../shared/umon/umonrtemsglue.c  \
     ../../shared/umon/monlib.c ../../shared/umon/tfsDriver.c \
-    startup/umonsupp.c
+    ../../shared/umon/umoncons.c startup/umonsupp.c
 
 if HAS_NETWORKING
 network_CPPFLAGS = -D__INSIDE_RTEMS_BSD_TCPIP_STACK__

c/src/lib/libbsp/arm/csb337/configure.ac

@@ -24,17 +24,21 @@ RTEMS_BSPOPTS_HELP([csb637],
 [If defined, this indicates that the BSP is being built for the
  csb637 variant.])
 
+RTEMS_BSPOPTS_SET([ENABLE_LCD],[*],[0])
+RTEMS_BSPOPTS_HELP([ENABLE_LCD],
+[If defined, enable use of the SED1356 controller and LCD.])
+AM_CONDITIONAL(ENABLE_LCD,test "$ENABLE_LCD" = "1")
+
+RTEMS_BSPOPTS_SET([ENABLE_UMON_CONSOLE],[*],[1])
+RTEMS_BSPOPTS_HELP([ENABLE_UMON_CONSOLE],
+[If defined, enable use of the MicroMonitor console device.])
+AM_CONDITIONAL(ENABLE_LCD,test "$ENABLE_UMON_CONSOLE" = "1")
+
 RTEMS_BSPOPTS_SET([BSP_PRESS_KEY_FOR_RESET],[*],[1])
 RTEMS_BSPOPTS_HELP([BSP_PRESS_KEY_FOR_RESET],
 [If defined, print a message and wait until pressed before resetting
  board when application exits.])
 
-RTEMS_BSPOPTS_SET([ENABLE_LCD],[*],[0])
-RTEMS_BSPOPTS_HELP([ENABLE_LCD],
-[If defined, enable use of the SED1356 controller.])
-
-AM_CONDITIONAL(ENABLE_LCD,test "$ENABLE_LCD" = "1")
-
 RTEMS_BSPOPTS_SET([BSP_RESET_BOARD_AT_EXIT],[*],[1])
 RTEMS_BSPOPTS_HELP([BSP_RESET_BOARD_AT_EXIT],
 [If defined, reset the board when the application exits.])

c/src/lib/libbsp/arm/csb337/console/uarts.c

@@ -32,16 +32,24 @@ rtems_device_minor_number  Console_Port_Minor = 0;
 extern console_fns dbgu_fns;
 #if ENABLE_LCD
   extern console_fns fbcons_fns;
-  #define NUM_DEVS       2
+  #define LCD_DEVICE     1
 #else
-  #define NUM_DEVS       1
+  #define LCD_DEVICE     0
 #endif
 
+#if ENABLE_UMON_CONSOLE
+  extern console_fns umoncons_fns;
+  #define UMON_CONSOLE_DEVICE 1
+#else
+  #define UMON_CONSOLE_DEVICE 0
+#endif
+
+#define NUM_DEVS   (1 + LCD_DEVICE + UMON_CONSOLE_DEVICE)
+
 /* These are used by code in console.c */
 unsigned long Console_Port_Count = NUM_DEVS;
 console_data  Console_Port_Data[NUM_DEVS];
 
-
 /* 
  * There's one item in array for each UART.
  *
@@ -90,6 +98,27 @@ console_tbl Console_Port_Tbl[] = {
     NULL,              /* setData - NOT USED */
     0,                 /* ulClock - NOT USED */
     0                  /* ulIntVector - NOT USED */
+  },
+#endif
+#if ENABLE_UMON_CONSOLE
+  {
+    "/dev/umon",       /* sDeviceName */
+    SERIAL_CUSTOM,     /* deviceType */
+    &umoncons_fns,     /* pDeviceFns */
+    NULL,              /* deviceProbe */
+    NULL,              /* pDeviceFlow */
+    0,                 /* ulMargin - NOT USED */
+    0,                 /* ulHysteresis - NOT USED */
+    NULL,              /* pDeviceParams */
+    0,                 /* ulCtrlPort1  - Pointer to UMON regs */
+    0,                 /* ulCtrlPort2  - NOT USED */
+    0,                 /* ulDataPort  - NOT USED */
+    NULL,              /* getRegister - NOT USED */
+    NULL,              /* setRegister - NOT USED */
+    NULL,              /* getData - NOT USED */
+    NULL,              /* setData - NOT USED */
+    0,                 /* ulClock - NOT USED */
+    0                  /* ulIntVector - NOT USED */
   }
 #endif
 };