Imagelibrary/rtems
1
0
Fork 1
mirror of https://gitlab.rtems.org/rtems/rtos/rtems.git synced 2025-12-26 14:18:20 +00:00
Code Issues Packages Projects Releases Wiki Activity

2001-11-16 Ralf Corsepius <corsepiu@faw.uni-ulm.de>

Browse Source 
* custom/eth_comm.cfg: Reflect changes to eth_comm/configure.ac.
	* custom/mbx8xx.cfg: Reflect changes to mbx8xx/configure.ac.
	* custom/mbx860_005b.cfg: Ditto.
	* custom/mpc8620ads.cfg: Reflect changes to mpc8620/configure.ac.
This commit is contained in:
Joel Sherrill
2001-11-20 18:55:30 +00:00
parent 5e0e4487d3
commit 708a87c51e
5 changed files with 8 additions and 123 deletions
Download Patch File Download Diff File Expand all files Collapse all files

6
make/custom/eth_comm.cfg
View File

@@ -16,10 +16,6 @@ RTEMS_PPC_EXCEPTION_PROCESSING_MODEL=new
# This section makes the target dependent options file.
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_ABI (PowerPC)
# This defines the calling convention (Application Binary Interface)
# used in this configuration. EABI is the only one supported.
@@ -36,10 +32,8 @@ define make-target-options
@echo "#endif" >>$@
@echo "#define mpc$(CPU_TYPE) 1" >>$@
@echo >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0000" >>$@
@echo "#define PPC_ABI PPC_ABI_EABI" >>$@
@echo "#define PPC_ASM PPC_ASM_ELF" >>$@
@echo "#define PPC_USE_SPRG 1" >>$@
endef
# This contains the compiler options necessary to select the CPU model

12
make/custom/mbx860_005b.cfg
View File

@@ -21,19 +21,7 @@ define make-target-options
@echo "#endif" >>$@
@echo "#define mpc$(CPU_TYPE) 1" >>$@
@echo >>$@
@echo "#define NVRAM_CONFIGURE 0" >>$@
@echo "#define UARTS_USE_TERMIOS 1" >>$@
@echo "#define CONSOLE_MINOR SMC1_MINOR" >>$@
@echo "#define UARTS_IO_MODE 0" >>$@
@echo "#define UARTS_USE_INTERRUPTS 0" >>$@
@echo "#define PRINTK_MINOR SMC1_MINOR" >>$@
@echo "#define PRINTK_IO_MODE 0" >>$@
@echo "/*#define EPPCBUG_SMC1 0*/" >>$@
@echo "/* #define EPPCBUG_VECTORS 1*/" >>$@
@echo "#define INSTRUCTION_CACHE_ENABLE 1" >>$@
@echo "#define DATA_CACHE_ENABLE 1" >>$@
@echo >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0000" >>$@
@echo "/*#define PPC_USE_DATA_CACHE 1*/" >>$@
@echo >>$@
endef

72
make/custom/mbx8xx.cfg
View File

@@ -64,57 +64,6 @@ endif # mbx821
#
# MBX8xx-specific options:
#
# NVRAM_CONFIGURE
# Define to 1 if you want the console driver, network driver and caches
# configured at boot time from parameters stored in NVRAM. If set to 1,
# most parameters below are ignored during the build. If not set to 1,
# then the console driver is configured at build time, the network host
# information is obtained from application supplied data structures, and
# the caches are configured at boot time based on the information supplied
# in this file.
#
# UARTS_USE_TERMIOS
# Define to 1 if you want termios support for every port.
# Termios support is independent of the choice of UART I/O mode.
#
# CONSOLE_MINOR (BSP--console driver)
# Must be defined to be one of SMC1_MINOR, SMC2_MINOR, SCC2_MINOR,
# SCC3_MINOR, or SCC4_MINOR. Determines which device will be registered
# as /dev/console.
#
# UARTS_IO_MODE (BSP--console driver)
# Define to 0 or 1 if you want polled I/O performed by RTEMS.
# Define to 1 if you want interrupt-driven performed by RTEMS.
# Define to 2 if you want polled I/O performed by EPPCBug.
# There is no provision to have a mix of interrupt-driven and polled I/O
# ports, except that the printk port may use a different mode from the
# other ports. If this is done, do not open the printk port from an RTEMS
# application. With EPPCBug 1.1, if mode 2 is selected, CONSOLE_MINOR must
# be set to SMC1_MINOR. This is a deficiency of the firmware: it does not
# perform serial I/O on any port other than its default debug port, which
# must be SMC1.
#
# PRINTK_MINOR (BSP--console driver)
# Must be defined to be one of SMC1_MINOR, SMC2_MINOR, SCC2_MINOR,
# SCC3_MINOR, or SCC4_MINOR. Determines which device is used for output
# by printk(). If the port that printk() uses is also used for other I/O
# (e.g. if PRINTK_MINOR == CONSOLE_MINOR), then both ports should use
# the same type of I/O, otherwise the drivers will likely conflict with
# each other.
#
# PRINTK_IO_MODE (BSP--console driver)
# Define to 0 or 1 if you want polled I/O performed by RTEMS.
# Define to 2 if you want polled I/O performed by EPPCBug.
# The printk() port is not configured to use termios. With EPPCBug 1.1,
# if mode 2 is selected, PRINTK_MINOR must be set to SMC1_MINOR.
# This is a deficiency of the firmware: it does not perform serial I/O
# on any port other than its default debug port, which must be SMC1.
# Printk always uses polled output.
#
# EPPCBUG_SMC1 (BSP--console driver)
# If defined, SMC1 is in use by EPPC-Bug. The console driver will not
# re-initialize that port.
#
# INSTRUCTION_CACHE_ENABLE (BSP--RTEMS)
# If defined, the instruction cache will be enabled after address translation
# is turned on.
@@ -123,16 +72,6 @@ endif # mbx821
# If defined, the data cache will be enabled after address translation
# is turned on.
#
# EPPCBUG_VECTORS (BSP--RTEMS)
# If defined, vectors branch to EPPCBug, except the following:
# 0x500 (external interrupt), 0x900 (decrementer).
#
# PowerPC-specific options:
#
# PPC_USE_DATA_CACHE (RTEMS PowerPC port)
# If defined, then the PowerPC specific code in RTEMS will use
# data cache instructions to optimize the context switch code.
# This code can conflict with debuggers or emulators.
define make-target-options
@echo "#ifdef mpc$(CPU_TYPE)" >>$@
@@ -140,20 +79,9 @@ define make-target-options
@echo "#endif" >>$@
@echo "#define mpc$(CPU_TYPE) 1" >>$@
@echo >>$@
@echo "#define NVRAM_CONFIGURE 1" >>$@
@echo "#define UARTS_USE_TERMIOS 0" >>$@
@echo "#define CONSOLE_MINOR SMC2_MINOR" >>$@
@echo "#define UARTS_IO_MODE 0" >>$@
@echo "#define PRINTK_MINOR SMC2_MINOR" >>$@
@echo "#define PRINTK_IO_MODE 0" >>$@
@echo "#define EPPCBUG_SMC1 1" >>$@
@echo "#define EPPCBUG_VECTORS 1" >>$@
@echo "#define INSTRUCTION_CACHE_ENABLE 1" >>$@
@echo "#define DATA_CACHE_ENABLE 1" >>$@
@echo >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0000" >>$@
@echo "#define PPC_USE_DATA_CACHE 1" >>$@
@echo >>$@
endef
# This contains the compiler options necessary to select the CPU model

33
make/custom/mpc8260ads.cfg
View File

@@ -13,15 +13,8 @@ CPU_TYPE=8260
# This is the actual bsp directory used during the build process.
RTEMS_BSP_FAMILY=mpc8260ads
#CPU_DEFINES=-DPPC_VECTOR_FILE_BASE=0x00000000
CPU_DEFINES=
# This section makes the target dependent options file.
# PPC_VECTOR_FILE_BASE (PowerPC)
# This defines the base address of the exception table.
# NOTE: Vectors are actually at 0xFFF00000 but file starts at offset 0x0100
#
# PPC_ABI (PowerPC)
# This defines the calling convention (Application Binary Interface)
# used in this configuration. EABI is the only one supported.
@@ -37,38 +30,12 @@ define make-target-options
@echo "#endif" >>$@
@echo "#define mpc$(CPU_TYPE) 1" >>$@
@echo >>$@
@echo "#define NVRAM_CONFIGURE 0" >>$@
@echo "#define UARTS_USE_TERMIOS 0" >>$@
@echo "#define CONSOLE_MINOR SCC2_MINOR" >>$@
@echo "#define UARTS_IO_MODE 0" >>$@
@echo "#define PRINTK_MINOR SCC2_MINOR" >>$@
@echo "#define PRINTK_IO_MODE 0" >>$@
@echo >>$@
@echo "#define PPC_VECTOR_FILE_BASE 0x0000" >>$@
@echo "#define PPC_ABI PPC_ABI_EABI" >>$@
@echo "#define PPC_ASM PPC_ASM_ELF" >>$@
@echo "#define INSTRUCTION_CACHE_ENABLE 0" >>$@
@echo "#define DATA_CACHE_ENABLE 0" >>$@
endef
# This section makes the target dependent options file.
# NDEBUG (C library)
# if defined asserts do not generate code. This is commonly used
# as a command line option.
#
# RTEMS_TEST_NO_PAUSE (RTEMS tests)
# do not pause between screens of output in the rtems tests
#
# RTEMS_DEBUG (RTEMS)
# If defined, debug checks in RTEMS and support library code are enabled.
#define make-target-options
# @echo "/* #define NDEBUG 1 */ " >>$@
# @echo "#define RTEMS_TEST_NO_PAUSE 1" >>$@
# @echo "/* #define RTEMS_DEBUG 1 */" >>$@
#endef
# This contains the compiler options necessary to select the CPU model
# and (hopefully) optimize for it.
#